- Order Placed with Factory Five
- Chassis Dolly Built
- Body Buck Built
- Car Arrived
- Inventoried Parts
- Front Lower Control Arms installed
- Front Upper Control Arms installed
- Front Hubs & Spindles installed
- Front Brakes installed
- IRS Carrier installed
- IRS Axles/Half-shafts installed
- IRS Control Arms installed
- IRS Knuckles & Hubs installed
- Tie rod ends painted
- Steering rack mounts modified for power steering rack
- Power steering rack installed
- Check the torque on all bolts and mark
- Install the oil pan
Tracking the Build Progress
Completed
Remaining Parts to Purchase
- Low Oil Level Sensor part# BL3Z-6C624-A Straight cut threads with O-ring seal.
- Battery (sized for Mustang GT)
- Tires: Nitto NT555 G2 Tires
- ABS parts
- Finishline Louvers, side vents http://www.finishlineaccessories.com/p-15-louvers-aluminum-side-vents.aspx
- HYDRATECH HBS9101 AN-6 RETURN LINE ADAPTER http://www.hydratechbraking.com/hose_fittings.html or Russell Performance Powerflex Lines http://russellperformance.com/mc/hose/powerflex.shtml
Remaining To-Dos
- Tack-weld nuts for quick jacks
- Move vertical tube in foot box
- Test fit custom foot box aluminum p.100
- Test fit firewall
- Powder coat custom foot box aluminum silver
- Reinstall the pedal box assembly and hydroboost in the driver’s footbox with spacer.
- Install accelerator pedal
- Install the steering shaft p.117
- Install the fuel tank & fuel pump p.127
- Check bellhousing alignment and index
- Bolt motor and trans together
- Test fit motor & trans in car
- Mark where to install brake/clutch reservoirs & fuel pressure regulator
- Check position of mid shifter and recut trans tunnel aluminum to fit
- Measure length for driveshaft
- Send driveshaft out to be resized to fit
- Remove motor and trans?
- Cut hole in rear cockpit panel for storage compartment.
- Install cockpit aluminum p.139
- Install fuel pressure regulator, fuel pump, fuel filter, & run fuel lines p.153
- Install brake & clutch fluid reservoirs p.160
- Run tubes from master cylinders to reservoirs
- Order remaining ABS parts
- Bench test ABS
- Install ABS
- Install brackets & flexible s/s brake lines front and rear p.167
- Layout brake line routing
- Run brake lines
- Tighten all brake fittings and banjo bolts & fill with brake fluid.
- Run the chassis wiring harness
- Install trunk aluminum
- Install rear cockpit compartment
- Install battery box
- Install battery
- Reinstall motor and trans
- Install driveshaft
- Install headers
- Hook up fuel lines to fuel rails on coyote
- Install clutch lines
- Install Drive by wire throttle cable??
- Install engine harness
- Mount computer
- Purchase radiator mount from Breeze
- Purchase coyote radiator hose from Breeze
- Mount fans to radiator
- Install radiator p.211
- Mount radiator inline filler neck and radiator hoses p.214
- Mount overflow tank and run hose from the filler p.217
- If needed, install the thermostatic fan switch provided to activate the fan.
- Install fan wiring p.221
- Install speedo sending unit p.221
- Purchase black Lokar e-brake handle & boot
- Install e-brake handle p.223
- Install e-brake cables (IRS) p.240
- Adjust e-brake handle/cable p.243
- Engine Ground p.246
- Install Axle & Fuel line vents p.248
- Order seat heaters
- Send seats, trans tunnel, and dash out for Alcantara
- Order Alcantara shift boot
- Install Transmission Tunnel Cover p.249
- Install Driver Footbox Side Aluminum p.251
- Order seat rails
- Install seats p.253
- Install name plate p.255
- Order dash blank
- Order glove box
- Design Dash
- Install seat heater wiring
- Cut custom competition dash pattern
- Powder coat dash black
- Powder coat dash supports black
- Powder gauge bezels black
- Install gauges p.256
- Install dash support mounts and dash
- Order any needed custom switches
- Mount switches
- Mount steering wheel p.266
- Order Breeze roll bars
- Order roll bar grommets
- Order windshield base trim
- Order Breeze windshield-mount mirrors
- Order windshield-mount rear-view mirror
- Tack-weld roll bars
- Send roll bars out for tig welding
- Powder Coat Roll bars black
- Powder Coat Side louvers black
- Powder Coat Headlight bezels black
- Powder Coat Wheels & spinners black
- Powder Coat Wipers black
- Powder Coat Quick jacks black
- Powder Coat Hood hinges black
- Powder Coat Hood handles black
- Powder Coat Door sill trim black
- Powder Coat Trunk latch black
- Powder Coat Headlight trim black
- Powder Coat Tail light trim black
- Powder Coat Lemans gas cap black
- Powder Coat License plate light black
- Powder Coat Windshield frame black
- Powder Coat Mirrors black
- Powder Coat Door latches black
- Paint fuel filler neck black
- Mount roll bars p.268
- Chassis check p.273
- Fill rear with 1.5 quarts 80w-90 gear oil and 5 oz friction modifier
- Install shifter
- Fill trans fluid
- Fill the engine with Oil and coolant.
- Grease suspension and steering
- Torque IRS Axle Nuts
- Order tires
- Mount tires on wheels
- Mount wheels/tires, then adjust ride height p.93
- Rattle patrol p.278
- Start & warm up engine p.279
- Go Kart time and check everything! P.279
- Foot box fitment
- Finish installing foot box aluminum p.281
- Install wiper mechanisms
- Prep frame & install weather stripping p.284
- Install the body p.286
- Install rear quick jacks p.287
- Install front quick jacks p.289
- Install and align hood p.290
- Install hood hinges p.292
- Install hood handles p.300
- Install the windshield p.306
- Install the doors p.308
- Adjust & trim doors p.310
- Install door latches p.312
- If necessary, Trim trunk edges enough to seat it in opening
- Order hydraulic lifts for trunk
- Install trunk hinges p.315
- Mount trunk hydraulic lifts
- Mount trunk p.317
- Mount trunk latch
- Test fit tail lights and turn signals, and adjust as needed p.323
- Install license plate light p.326
- Test fit the light bucket p.331
- Remove hood & Install hood scoop p.333
- Order Alex’s Fender liners
- Spray LineX bedliner under body.
- Prep the body p.340
- Send body to paint p.341
- Purchase sealant for gaps
- Purchase aluminum Tape
- Seal all aluminum edges p.351
- Purchase sound & heat insulation
- Install sound & heat insulation
- Install radiator aluminum p.343
- Remove seats
- Install carpet p.353
- Install seat floor & lap harnesses p.358
- Install e-brake boot p.360
- Seat final install p.362
- Install seat harness shoulder belts p.362
- Install shifter handle & boot p.366
- Order custom headlights
- Install headlights p.369
- Install tail lights p.376
- Install Lemans gas cap p.377 – make sure to change the hardware (every nut, bolt, and washer) to all stainless steel.
- Install side louvers p.380
- Finish installing the weatherstripping p.382
- Fit the body back on the chassis p.385
- Reinstall the quick jacks p.385
- Rivet the hood scoop to the hood an install hood to car p.386
- Install roll bar grommets
- Install roll bars p.387
- Install doors p.388
- Install windshield p.389
- Ground and install the fuel filler neck p.390
- Install fuel tank access covers p.393
- Final trunk mounting p.393
- Install side & rearview mirrors p.395
- Install light wiring p.403
- Order Dye
- Dye check straps black
- Install check straps p.404
- Install under door aluminum, carpet and weatherstripping around door p.406
- Order custom badges & steering wheel center cap logo
- Install steering wheel center cap p.408
- Order Drummer Mike side exhaust shields
- Ceramic coat side exhaust & shields black
- Install side exhaust w/ DW custom mounts p.410
- Trim & adjust front aluminum splash guards for wheel/tire clearance p.415
- Trim & adjust rear wheel aluminum splash guards for wheel/tire clearance p.418
- Mark and drill holes in front aluminum splash guards and pre-drill the frame for them p.415
- Mark and drill holes in rear wheel aluminum splash guards and pre-drill the frame for them p.418
- Treat front splash guards with undercoating
- Treat rear wheel splash guards with undercoating
- Install front aluminum splash guards p.417
- Install rear wheel aluminum splash guards p.418
- Align the headlights p.423
- Align the suspension p.423
- Install sun visors
- Install wind wings
Install bumpers